SET of ANEL Double-Body Hive with 20 Wooden Frames and Ventilated Mobile Bottom Board Langstroth

The NEW ANEL propolis collection screen bears two holes that you can choose to open if you want to put solid food on top (bee candy). Thus, you will be able to feed the bees and at the same time they will not stop the collection of propolis. The sides of the holes also lift the center of the screen up so it does not bend in the center and the bees can fill all the screen evenly.
Propolis is a very promising product with a very good price, which may contribute to your income without requiring much effort or time. The propolis collection screens are placed on the hive top floor, below the cover.
There should be some space left above the propolis collection screen and the hive cover so that air current is generated from which the bees will try to protect themselves by filling the screen with propolis. To keep the required gap you can use the two spacers attached to the side of the screen which are foldable. Propolis can be extracted from the screens after you place it in the freezer for 5 minutes and then shake or rub the propolis with a piece of wood or your hand.
The screen can collect 60 to 80gr when full within 10-15 days. Usually applied in spring and autumn - a good year can give you around 400gr per beehive. All these results can vary depending on the race of the bees, the beehive, the fauna and the time of year.
Screen dimensions: 420x510mm - can be cut to any smaller dimensions you wish!
Gaps dimensions: 20,5x2,5mm
Weight: 0,264kg
Material: Polyethylene (PE), Food Grade

A plastic frame with integrated plastic foundation with perfectly printed hexagons (5,6 mm). No wiring or riveting necessary. Resistant to wax moths. It does not get unfastened or loose and does not “sag”. You can use higher speeds in the honey extractor without destroying the comb (especially useful for thick honey types such as fir). All ANEL plastic frames are available waxed or unwaxed. If you want to wax ANEL frames yourself you can either dip them in molten wax (temperature 60-70⁰C) or wax them using a roll dipped into molten wax. TIP: The ANEL frames can be disinfected in a solution of caustic potash 5% at 80⁰C.

An innovative new ANEL Product! This is the New Hybrid ANEL Entrance, Ventilation & Feeding Plug.
Multiple uses:
• Ventilation screen and/or feeding plug.
• If you rotate the mechanism, with a simple CLICK, it turns into a small safety entrance for bees.
• Remove the mechanism altogether and you can use it as big entrance or a feeding plug.
To apply it in your beehive you will need:
• A drill with a 43mm hole saw
• Four 3,5 x 13mm screws
• A Polyurethane Sealant
We apply the PU sealant in the inner surface of the plug. We follow the same steps for a wooden beehive. The new ANEL plug is of larger diameter than the previous model. To replace the older model with the new plug you will need a 43mm cylindrical drill. The new plug comes with a hinge and opens sideways. It is advised to open it with a hive tool while holding it from the top, or by hand using our thumbnails. Due to opening sideways the plug cannot be closed by the wind. Position the lid in 90 degrees from the body to remove it. This is very useful because a potential thief will need special equipment.
The new ANEL Entrance, Ventilation & Feeding Plug can be used in many ways. As a feeding plug on the top cover, as ventilation or entrance in the frontside / backside of the top cover, as a small entrance on the side of the beehive protecting the bees from potential enemies, as ventilation on the sides, or as a big hive entrance. An alternative beehive entrance is very important. In case of plunder we leave the small entrance open so that only few bees can come in and the intruders can be handled. We close the front doors and lead the bees on the alternative entrance which the already know and use. For even more drastic measures if we want to prevent plunder, we just seal the plugs on the top cover.
Some other examples of how to use the New ANEL Entrance, Ventilation & Feeding Plug. During spring if we want to use a second hive body, it is very useful to have a second entrance in the upper hive body for beehive decongestion. A second entrance also helps bees collect honey easier, especially if we use a queen excluder.
Also, during spring if we have a ten-frame beehive that is in the process of swarming, we can divide it and have two independent swarms. Half of the frames can be transferred to a new hive body. We use a fabric cover to prevent pheromones from mixing and a queen excluder to keep the two queens away from each other. We place the new hive body on top. The original swarm uses the front entrance, while the new one uses the entrance on the back.
If we want to have 2 swarms in a single beehive, we can provide them two independent entrances from both sides. We keep them divided in two with the help of the ANEL vertical beehive divider. We can also have 3 swarms in the same beehive with the use of 2 dividers. This swarm uses the entrance on the right, this one uses the entrance on the left and the middle swarm uses the entrance on the back. In that case we will need a top feeder to keep them separated and feed them independently with syrup or candy.